|
|
GEO help: Mouse over screen elements for information. |
|
Status |
Public on Aug 20, 2019 |
Title |
human HEK293T H3K4me3 - 83 |
Sample type |
SRA |
|
|
Source name |
HEK293T
|
Organism |
Homo sapiens |
Characteristics |
cell lines: HEK293T
|
Extracted molecule |
genomic DNA |
Extraction protocol |
HEK293T cells were washed with PBS and permeabilized using a 10 min incubation on ice in 500 mL of complex formation buffer per ~1 million cells. After permeabilization, all subsequent centrifugations of cells were performed using the following procedure: 1 min spin at 250 *g, rotate tubes 180°, repeat spin, leave ~10 mL of solution in the tube when removing buffer. Pelleted cells were washed once with 500 mL of complex formation buffer and suspended in another 500 mL of buffer. Aliquots of 1,000 cell equivalents were transferred volumetrically to clean microcentrifuge tubes and adjusted to 50 mL total volume using complex formation buffer. 5 mL of antibody-bound PA-Tnp complex was added to each 50 mL cell aliquot and incubated at room temperature for 60 min to allow chromatin binding. Unbound complex was removed using three washes performed as follows: pellet and suspend cells in 500 mL of wash buffer (50 mM Tris pH 8.0, 150 mM NaCl, 0.1% Triton X-100), rotate tube for 8 min at room temperature, repeat. Pelleted cells were rinsed with 500 mL of rinse buffer (50 mM Tris pH 8.0, 50 mM NaCl, 0.1% Triton X-100). The rinse buffer was removed and 90 mL of reaction buffer (50 mM Tris pH 8.0, 150 mM NaCl, 10 mM MgCl2, 0.1% Triton X-100) was added to the pelleted cells for a total volume of ~100 mL. The tubes were incubated for 30 min at 37 °C to allow transposition to occur. The reaction was terminated by addition of 4 mL of 0.5 M EDTA, 2 mL of 10% SDS, and 1 mL of 20 mg/mL Proteinase K followed by a 60 min incubation at 65 °C. DNA was purified using phenol-chloroform-isopentanol extraction and ethanol precipitation. The DNA pellet was suspended in 10 mL of 10 mM Tris pH 8.0. PCR reactions for library preparation were performed by adding the following to the 10 mL DNA sample: 25 mL of Phusion High-fidelity PCR Master Mix (NEB catalog # M0531S), 1 mL of 5¢ library index barcode, 1 mL of 3¢ library index barcode, and 13 mL of nuclease-free water. Amplification was performed using an initial step of 72 °C for 5 min followed by 15 cycles of: 98 °C for 10 s, 65 °C for 30 s, 72 °C for 15 s, and a final extension step of 72 °C for 5 min. The PCR products were analyzed using agarose gel electrophoresis. Fragments of the desired size were excised and purified using a QIAquick Gel Extraction kit (Qiagen cat # 28506). scACT-seq
|
|
|
Library strategy |
OTHER |
Library source |
genomic |
Library selection |
other |
Instrument model |
Illumina HiSeq 3000 |
|
|
Description |
scACT-seq
|
Data processing |
Basecalls performed using RTA 1.7 or Illumina Casava1.7 Read in the raw fastq files are separated into 96 files correponding to the 96 pairs of cell barcode. The 96 pairs of barcodes are shown in the file named barcode_96.txt. A read is considered to belong to one of the barcode if the beginning of correpsonding read1 or read 2 contain the same pair of barcodes in theleft and right column respectively. After separting each set of fastq files into 96 set of files, the 34bp starting from 5' is trimmed and the remainging reads are mapped to human genome using bowtie2. Since 18 nuclei is sorted for each well, we removed doublets and the top 14 ranked barcodes are considered to be cells. The doublets and the number of 14 were calculated based on the collision rate the same as in the reference (Science. 2015 May 22; 348(6237): 910–914. ) . With requiring the qualified cells have reads more than 500, 1246 single cells are obtained. On the other hand, Using the publsihed HEK293T DNase-seq data, we identified 15756 DHS (as shown in the file called peaks_15756_HEK293T.txt). For each cell, we calculated the reads that were located within the DHS. Finally, we obtained a read count file for the single cells, in which the 1246 columns referred to single cells, and the 15756 rows refer to 15756 DHS regions. Genome_build: hg18 Supplementary_files_format_and_content: barcode_96.txt: 2column. The left column refer to barcode on read 1 starting from the 5' end while The right column refer to barcode on read 1 starting from the 5' end Supplementary_files_format_and_content: peaks_15756_HEK293T.txt: the first column is chromsome, 2nd column is the start of DHS, 3rd column is the end of DHS Supplementary_files_format_and_content: scH3K4me3_1246_cells_counts_at_293T.txt: This file contain the read count data of single cells. Each column refer a single cell and each row refer to a DHS, resulting in a matrix of 15756 x 1246. Each element in the matrix represent the number of reads from the single cell located within the DHS.
|
|
|
Submission date |
Jan 31, 2019 |
Last update date |
Aug 20, 2019 |
Contact name |
Keji Zhao |
E-mail(s) |
zhaok@nhlbi.nih.gov
|
Organization name |
national Institute of Health
|
Department |
National Heart, Lung, and Blood Institute
|
Street address |
Building 10 Room 7B06A
|
City |
Bethesda |
State/province |
MD |
ZIP/Postal code |
20814 |
Country |
USA |
|
|
Platform ID |
GPL21290 |
Series (1) |
GSE125971 |
Mapping Histone Modifications in Single Cells Using an Antibody-guided Transposase |
|
Relations |
BioSample |
SAMN10854012 |
SRA |
SRX5317434 |
Supplementary data files not provided |
SRA Run Selector |
Raw data are available in SRA |
Processed data are available on Series record |
|
|
|
|
|